E Series Classic Software

If the firmware process is interrupted your product may not function properly, therefore do not interrupt the process and ensure the unit is on a reliable power supply. Damage caused by incomplete upgrades will not be covered by Raymarine warranty.

By Downloading the software, you agree to these terms.

Software history

• Current version

• Improved AIS performance including increase of Class B AIS target time-out period to prevent the MFD unnecessarily dropping AIS targets and providing correct TCPA calculation of both stationary and active AIS targets.

• Digital Radome support - Raymarine has made provisions to insure all E-Series Classic Multifunction Displays possess full compatibility with the Digital Radome product line.
• AIS Class B support - Further expanding on Raymarine's AIS capabilities, software v5.52 now provides E-Series Classic with AIS Class B support, including silent mode and buddy tracking.
• Foreign language support for chart labels - E-Series Classic software v5.52 brings with it the addition of Unicode support, providing users the ability to display actual chart labels in a number of foreign languages (foreign language availability dependent upon purchased Navionics cartography).
• SeaTalkng Support - With 5.52 software, the E-Series Classic MFDs can now be connected to a full SeaTalkng based installation (Support for AIS500 in SeaTalkng still pending).
• Datum Selection - GPS Datum selection error previously reported earlier in the summer has now been corrected in this software release.
  • Autopilot
    • Additional autopilot status symbols within fishing pattern mode
    • Improved alarm handling for SeaTalkng autopilot
    • Added Buddy Tracking and Silent Mode functionality
    • Addressed rebooting when a large number of AIS targets are in range (Greater than 300 targets)
    • Corrected issues with AIS Target List, simulator function and input to repeater display
    • Improved handling of AIS alarm acknowledgement
    • Added capability to adjust route line thickness and color
    • Addressed E-Series Classic Repeater display crashing when databar is switched off
    • Resolved transducer speed display when using "Y" cable
    • Improved SeaTalkhs data communications with Digital Sounder Modules
      • We also strongly recommend that DSM30s, DSM300s, and DSM300Gs which have been interfaced to SeaTalkhs MFDs (ex. E-Series Classic MFDs, E-Series Widescreen MFDs, C-Series Widescreen MFDs, and G-Series GPMs) be upgraded to v4.20 DSM30/300 software with v5.18 bootcode. This DSM software may be downloaded from the Downloads & Updates tab found on the DSM30 and DSM300G's product web page
      • Fixed SD satellite not being shown on GPS status page
      • Corrected wrong vessel position when not in WGS84 datum
      • Addresses incorrect position shown in GPS status box
      • Corrected a missing text string in the radar application when using Italian language
      • Implemented changes to NOAA Marine Zone Boundaries (Great Lakes and others) to support Marine Zone forecast feature
      • Resolved data buffer of large storm systems resulting in system crash
      • Fixed SIRIUS Receiver 12-digit ID not being displayed correctly
      • Fixed SIRIUS Audio alerts softkey not enabled and Delete Alert not initializing
      • E-Series Classic MFD no longer reboots after 45 minutes inactivity
      • Master E-Series Classic MFD no longer crashes following the Repeater E-Series Classic MFD being switched off
      • Maintenance Release: US ONLY

      Maintenance Release: UK/EU/ROW ONLY

      • Digital Radome support
      • Enhanced AIS Class B support
      • SeaTalkNG support
      • Correct a missing text string in the radar application when using Italian language
      • Introduction of new Flash Memory
      • Enable changes in WAAS functionality
      • Erroneous IP Address 10.6.x.x
      • Default radar settings
      • NGS Analogue Radar support
      • Sirius Weather support
      • AIS / Navtex support
      • Support for Navionics Platinum cartography
      • Unit resets when selecting French language
      • Improve ST2 Keyboard compatibility
      • Initial Release

      Open Source GPL/LGPL

      Some Raymarine products contain software code developed by third parties that are covered by open source GPL and LGPL software license agreements. You can view the third party license agreements by visiting the Manuals section of our website.

      To access the open source GPL and LGPL licensed executables click here

      Software Update Information and Instructions for Raymarine Legacy Multifunction Displays

      This FAQ relates to the following products:

      • a Series - a65, a67
      • c Series - c95, c97, c125. c127
      • e Series - e7, e7D, e95, e97, e125, e127, e165
      • gS Series - gS95, gS125, gS165
      • Dragonfly
      • A Series - A50, A50D, A57, A57D, A70, A70D
      • C Series Classic - C70, C80, C120
      • E Series Classic - E80, E120
      • C Series Wide - C90w, C120w, C140w
      • E Series Wide - E90w, E120w, E140w

      The following procedure addresses how one would populate a Flash memory card (Compact Flash/mSD) with software update files for the Multifunction Display (MFD) and then use this Flash memory card to update the MFD's software. Please note that product software updates may revert some MFD configuration settings back to the MFD's default settings. As such, it is recommended that customers make note of the MFD's configuration settings so that they may be used to reconfigure the MFD's settings after the MFD's software has been updated.

      Populating a Flash Memory Card (Compact Flash/mSD) with the MFD Software

      Note: microSD memory cards used with a/c/e/gS Series MFDs should have a memory capacity of no less than 512MB and no more than 32GB. CompactFlash cards should not exceed 128MB in size. Please note that CompactFlash cards greater than 2GB total capacity must not be used as there may be a risk of hardware damage to early C and E Classic displays. This limitation also applies to cartography that is contained within a 2GB partition on a higher capacity CompactFlash card - the cartography can only be used on a card no greater than 2GB total capacity.

      Note: To avoid potentially corrupting the data on your chart card, DO NOT copy software update files to your chart card and DO NOT back up waypoint/route/track data to your chart card. MicroSD cards are commonly available in most stores selling consumer electronics products. Waypoint, route, track data, and system configuration data can be stored on a microSD memory card which also contains software update files.

      1. Insert a compatible Flash memory card into the computer's memory card reader or into a memory card reader which has been interfaced to the computer.
         
      2. Select the appropriate software download for your product
      3. Upon completion of the download, click on the downloaded file to open it
      4. Copy all files to the Root of the Flash card (Root is the first level you access when selecting the Flash). Make sure the files are not in any folders on the card (See video below for examples. Files will vary depending on update)

      For example, if your computer has assigned Removable Disk (E:) to your memory card reader/writer, then the software update files should be copied directly to Removable Disk (E:), not to any folders created on the memory card.

      Backing Up Your Waypoints, Routes and Tracks

      It will be necessary to reset the MFD as the final step in the process of updating it. This procedure WILL erase any of the waypoints, routes and tracks that are currently stored within the MFD.

      The steps for restoring this data to the MFD are also contained in this same FAQ.

      Note: one may use a single Flash memory card to both backing up the data within one’s MFD as well as for performing the software update. When using this Flash memory card for backing up the data within one’s MFD, be certain to not insert the memory card into the MFD’s memory card reader/writer until the MFD has been powered up and has completed its startup initialization.

      Updating the MFD Software

      The next stage is to update your MFD. Please choose the appropriate instructions below depending on what MFD you are using to perform the update. This update must be performed on all connected MFD's in the system. If there is connected MFDs in the system with different software versions you may experience spurious issues.

      Note: Software updates do not have to be performed sequentially unless stated. It is fine to update from version 2.00 to version 5.00 and miss both version 3.00 and 4.00 if you have not previously installed them. All necessary information for the units to operate are included in the latest update.

      IMPORTANT TERMS OF DOWNLOADING SOFTWARE

      This firmware update process is done at your own risk. Before initiating the update process be sure to backup and make copies of all important files.

      If the firmware process is interrupted your product may not function properly, therefore do not interrupt the process and ensure the unit is on a reliable power supply. Damage caused by incomplete upgrades will not be covered by Raymarine warranty.

      By Downloading the software, you agree to these terms.

      NOTE: When upgrading to LightHouse 3.6 please ensure the DJI Radio Controller is NOT connected to the MFD.

      Updating the a, c, e or gS Series MFD Software

      1. Power OFF the MFD.
      2. Insert the mSD card containing the software update files into the MFD’s memory card reader.
      3. Power ON the MFD.
      4. Wait until the screen notifies you that the software update has completed (this can take time, DO NOT power down the display during this procedure) and remove the mSD card.
      5. Reboot the unit (c/e Series will do automatically, a/gS Series you need to turn power off to the display)
         • At this point, if you have additional MFD's or any accessories that are eligible to be updated, you will be prompted to update these too. Follow the onscreen instructions
      6. Once all the devices in the system are updated, please verify that this is correct by going to the following screen:
         • The MFD's software version may be verified via the command sequence [Home screen] Setup > Maintenance> Diagnostics > Select Device

      IMPORTANT RESET INFORMATION

      Historically, the Raymarine Technical Support teams have encouraged users to perform the power-on reset (also, known as factory reset, hard reset or master reset) on the Multifunction display products after a software upgrade. This nature of reset is not deemed necessary when upgrading with the Lighthouse II Release 11.xx software.

      However, should you feel there is any reason to perform a reset, you should only have to perform the “Settings Reset” within the menu (Set-Up / Maintenance / System Settings Reset). This will retain the waypoints/ routes & tracks in the unit. The “Power-on Reset” should only be required if the MFD will not boot correctly

      CP300 / CP450C owners

      If you also have a CP300 or a CP450C and you want to take advantage of all the features in the latest SONAR software, then you will also need to upgrade your sonar module. You can download a detailed flow diagram that will guide you through the steps or alternatively, please contact your local Raymarine dealer for assistance.

      Updating the A Series, C Series Classic/Wide, E Series Classic/Wide MFD's Software

      1. Power OFF the MFD.
      2. Insert the CF memory card containing the software update files into the MFD’s memory card reader.
      3. Power ON the MFD.
      4. After the MFD has booted to its Raymarine Software Upgrade Utility screen, select the software upgrade package from the Upgrade Packages Available list.
      5. Press the UPGRADE THIS UNIT function key.
      6. When the progress indicator's Overall bar reaches 100%, the MFD's software will have been upgraded.
      7. Remove the CF memory card from the MFD's memory card reader.
      8. Press MFD's red power button to power OFF the MFD.
      9. Press and hold the first (Left Hand) softkey on the MFD. Keeping the softkey held down, press the red power button to power ON the MFD. This will perform a reset of the unit. Do not skip this step.
         The unit will notify you that the reset has completed after the count down by a beep. You can now release the softkey.

      • The MFD's software version may be verified via the command sequence MENU->SYSTEM DIAGNOSTICS->SOFTWARE SERVICES->UNIT INFO; Inspect the item labeled APP VERSION